500 LPH RO Plant, Commercial RO Plant 500 LPH
Modern commercial reverse osmosis system with multi-stage filtration for reliable water treatment applications.
Image for presentation only. Actual product design may vary.
500 LPH RO Plant for Commercial Water Treatment
The 500 LPH RO Plant is a compact commercial reverse osmosis system designed for applications that require a continuous supply of treated water. According to the supplied system specification, the plant is configured for a production capacity of approximately 500 litres per hour.
The system combines pre-treatment, anti-scalant dosing, micron filtration, high-pressure pumping and RO membrane filtration in a single treatment scheme. It can be used where treated water needs to be collected in dedicated storage tanks or supplied to commercial facilities.
About 500 LPH RO Plant
A Practical Commercial RO Solution
A 500 LPH commercial RO plant is intended for sites that need treated water on a regular basis without moving to a larger industrial-capacity system. The supplied configuration includes pre-treatment filters, anti-scalant dosing, micron filtration, a high-pressure pump and reverse osmosis membranes.
The system specification provided for this page is based on feed-water conditions and operating parameters listed below. Actual performance can vary depending on source-water quality, temperature, pressure, membrane condition and site installation.
Technical Assumptions
| Component | Specification |
|---|---|
| Feed Water TDS | 1000 ppm |
| Fluorides | < 1 ppm |
| Iron | < 0.1 ppm |
| Turbidity | < 5 NTU |
| pH Range | 6.5 - 7.5 |
Purification Scheme
| Component | Specification |
|---|---|
| Feed Water TDS - Standard | 1000 ppm |
| Feed Water TDS - Maximum | 2500 PPM |
| Product Water Output | 500 LPH |
| Recovery Rate | 60% |
| Salt Rejection Rate | 95% |
Detailed Component Specifications
01 Feed Water Pump
Requires an inlet pressure of minimum 1.5 Kg/cm² for smooth operation.
| Component | Specification |
|---|---|
| Make | CG |
| Power | 1 HP |
| Volts | 230 V |
| Phase | Single Phase |
| Type | Mono Block |
02 Pressure Sand Filter
Ensures low-turbidity water feeding and filtration down to approximately 30 microns. The configuration uses a non-corrosive vessel, multi-graded silica sand and a multi-port valve for backwash and rinse functionality.
| Component | Specification |
|---|---|
| Vessel Material | FRP |
| Size | 12" × 48" |
| Volume | 80 Liters |
| MPV | 25 NB Top Mounted |
| Operating Pressure | 1.5 - 4.5 kg/cm² (Average 2-3 kg/cm²) |
03 Active Carbon Filter (ACF)
The active carbon stage is specified for reducing chlorine, color, odor and dissolved gases before the water reaches downstream RO components.
| Component | Specification |
|---|---|
| Vessel Material | FRP |
| Size | 12" × 48" |
| Volume | 80 Liters |
| Media | Activated Carbon |
04 Anti-Scalant Dosing System
Doses anti-scalant chemical in controlled quantities to help reduce scale formation on RO membrane surfaces.
| Component | Specification |
|---|---|
| Make | Altawel / E-Dose |
| Type | Diaphragm Metering Pump |
| Capacity | 6 LPH |
| Dosing Tank | 100 Ltr Plastic Drum |
05 Micron Filter
Provides final pre-filtration for particles above the specified micron rating before water enters the high-pressure RO stage.
| Component | Specification |
|---|---|
| Housing | PP Jumbo Housing |
| Micron Rating | 5 Micron |
06 High Pressure Pump
Boosts system pressure to the specified 8–14 Kg/cm² operating range required for the reverse osmosis stage.
| Component | Specification |
|---|---|
| Make | CRI / Lubi / Shigme |
| Type | Horizontal Multi-Stage |
| Maximum Pressure | 17 Kgs/cm² |
| Operating Pressure | 8–14 Kgs/cm² |
07 Membrane Housing & Membranes
The supplied specification uses Thin Film Composite (TFC) membranes with a stated filtration level of approximately 0.0001 micron and up to 95% salt rejection under specified operating conditions.
| Component | Specification |
|---|---|
| Membrane Make | Hydranautics / CSM / Vontron/ Others |
| Specs | 4040 (2 Elements) |
| Housing Material | FRP (Single Element Shell) |
| Operating Pressure | 9–14 Kgs/cm² |
System Accessories & Piping
| Component | Specification |
|---|---|
| Control Panel | Plastic MOC, Single Phase, Inbuilt Conductivity Meter, LPS/HPS Adjusters |
| Wet Panel | SS MOC, 2 Flow Meters, 4 Pressure Gauges, LPS & HPS Sensors |
| Skid Construction | Stainless Steel Frame |
| Piping Lines | UPVC (Food Grade Compliant as per FDA & NSF) |
500 LPH RO Plant – Key Points
Need a 500 LPH RO Plant?
Contact Gaurav Water Solution for product enquiries, pricing and installation-related information for the 500 LPH commercial RO system.
Before Installation
The technical values displayed on this page are based on the supplied 500 LPH RO Plant specification. Final system selection and performance should be evaluated against actual source-water quality and site requirements.
For feed water with high turbidity or conditions outside the listed assumptions, additional pre-treatment may be required. Please contact the Gaurav Water Solution team before installation for site-specific requirements.