250 LPH RO Plant, Commercial RO Plant 250 LPH
Commercial reverse osmosis water purification with a multi-stage filtration system.
Image for presentation only. Actual product will be different from the product shown.
250 LPH RO Plant suitable for home and office use. In whole day approx give 2500 liter to 3000 liter pure water. Store this water for your home or staff.
Use raw water 300 TDS to 2000 TDS in Commercial ro plant 250 lph. That's output in TDS approximately 50 to 150 TDS.
You have to store water in water cooler or water tank as suitable to you.
250 LPH Commercial RO Plant for Daily Water Needs
The 250 LPH commercial RO plant is designed for applications that need a steady supply of purified water. It can be considered for offices, workplaces, small commercial facilities and other sites where water demand, raw-water quality and storage requirements have been assessed.
The system uses multiple treatment stages, including pre-filtration, chemical dosing, micron filtration and reverse osmosis. These stages help prepare feed water for the RO membrane and support the system's water-treatment process. Actual output and treated-water quality depend on feed-water conditions, system setup and maintenance.
Before selecting a plant, review the raw-water test report, required daily quantity, available installation space, drainage and storage arrangements. Our team can help discuss the application and the configuration needed for your site.
250 Liters Per Hour RO Plant
Description
Technical Details:
ASSUMPIONS
| Description | Specification |
|---|---|
| FEED WATER TDS | 1000ppm |
| Fluorides | < 1 ppm |
| Iron | < 0.1 ppm |
| Turbidity | < 5 |
| pH | Less than 7.5 and greater than 6.5 |
Scheme:
| Description | Specification |
|---|---|
| FEED WATER | 1000PPM |
| FEED WATER TDS | 1000PPM |
| PRODUCT WATER | 250LPH |
| RECOVERY | 60% |
| SALT REJECTION | 95% |
In case of high Turbidity customer needs to provide a settlement tank and Alum dosing system is to be incorporated. The cost of the same has not been considered with in the scheme.
TECHNICAL SPECIFICATION
FEED Water Pump
The system would require an Inlet Pressure of 1.5 Kg/cm2 minimum for smooth operation. To provide the same the Raw Water Pump is being incorporated in the system.
Description
| Description | Specification |
|---|---|
| Make | CG |
| Power | 1 Hp |
| Volts | 230 volts |
| Phase | Single |
| Type | Mono Block |
PRESSURE SAND FILTER
The system is required to be feed with "0" turbidity water. The Pressure Sand Filter is incorporated in the system to ensure the same. The Pressure Sand Filter offers a filtration up to 30 microns.
The Filter consists of a Non Corrosive Vessel that can withstand pressure up to 6.5 Kgs/cm2, Multi Graded Sand Filtration Media for filtration, Internal Distribution System to distribute the water evenly inside the vessel for proper filtration, Multi Port Value (MPV) for easier operation along with Back Wash and Rinse facilities, a stand to hold the MPV in position and Pressure Gauges to know the position of the sand filter.
The filter is designed for 14m/sec internal flow for proper filtration.
Description
| Description | Specification |
|---|---|
| Vessel | FRP |
| Size | 8"44" |
| Volume | 34 Lts |
| Multi Port Value Filter | 25 Nb Top Mounted |
| Media | Silica Sand Multi Grade |
| Min Operating Pressure | 1.5kg/Cm2 |
| Max Operating Pressure | 4.5kg/Cm2 |
| Avg Operating Pressure | 2-3kg/Cm2 |
ACTIVE CARBON FILTER (ACF)
This system is required to be feed with NIL Chlorine water. The Activated Carbon Filter is incorporated in the system to ensure the same. It also ensures that the water is color less, odor less and contains no dissolved gases.
The Filter consists of a Non Corrosive Vessel that can withstand pressure up to 6.5Kgs/cm2, Multi Graded Sand and Activated Carbon Filtration Media for filtration, Internal Distribution System to distribute the water evenly inside the vessel for proper filtration, Multi Port Value (MPV) for easier operation along with Back Wash and Rinse facilities, a stand to hold the MPV in position and Pressure Gauges to know the position of the Activated Carbon filter.
The filter is designed for 14 m/sec internal flow for proper filtration.
Description
| Description | Specification |
|---|---|
| Vessel | FRP |
| Size | 8"44" |
| Volume | 34 Lts |
| Multi Port Value | 25 Nb Top Mounted Filters |
| Media | Activated Carbon |
| Min Operating Pressure | 1.5kg/Cm2 |
| Max Operating Pressure | 4.5kg/Cm2 |
| Avg Operating Pressure | 2-3kg/Cm2 |
ANTI SCALENT DOSING SYSTEM
The ANTI SCALENT DOSING SYSTEM gives the system an extra protection towards any kind of scale formation over the membranes. Chemicals are chosen depending on the water analysis report of the raw water. These chemicals are dosed in the water inflow drop by drop. The chemicals agitate the dissolved particles in the water so as not to allow them to settle down on the membrane surface.
Description
| Description | Specification |
|---|---|
| Make | Altawel/E-Dose |
| Type | Diaphragm Type Metering Pump |
| MOC of Diaphragm | PP |
| Capacity | 6 LPH |
| Drum (100 Ltr) | Plastic |
| Anti Scalent Chemical | 1 Litre |
MICRON FILTER
Due to the induction of the dosing chemical some of the particles may coagulate in the water. This coagulated particle cannot be allowed to enter the membrane. The Micron Filter ensures that all such particles above the size of 5 micron are being filtered out of the water so as to enhance the system life. It also ensures that even all un dissolved particles above the size of 5 Micron are being filtered out.
Description
| Description | Specification |
|---|---|
| No. Offered | One |
| Jumbo Housing | PP |
| Specs | One |
| Filters Nos. Offered | One |
| Micron Rating | 5 Micron |
HIGH PRESSURE PUMP
In the system, the membrane filtration takes place at high pressure only in the range of 8-14 KG/CM2. To provide such high pressure the Pressure Booster Pump is being induced in the system to boost the pressure to the required level for the proper filtration process.
Description
| Description | Specification |
|---|---|
| Make | PURE & CURE |
| Power | Single Phase |
| Type | Horizontal Multi Stage |
| Pressure Rating | 1.5 M3 At 140m Head |
| Max Pressure | 17 Kgs/Cm2 |
| Normal Operating Pressures | 8-14 Kgs/Cm2 |
MEMBRANE HOUSING
The membrane housing provides the shell for the membranes to allow the highly pressurized water to pass through the membrane.
Description
| Description | Specification |
|---|---|
| MOC | FRP |
| No. Offered | One |
| Specs | 4:40 (Single Element) |
| Max Pressure | 21 Kgs/ Cm2 |
| Operating Pressure | 9-14 Kgs/ Cm2 |
MEMBRANE
The system consists of Thin Film Composite Membrane made out of Poly Urethane acetate that provides a filtration level up to 0.0001 micron. These operate at a pressure between 9-14 kgs/cm2 this result in a dissolved salt rejection of up to 95%. The membrane separates the water into two streams. One is the premed or the product water and the other is the rejection.
Description
| Description | Specification |
|---|---|
| Specs | 4040 |
| No. Offered | One |
| Operating Pressure | 9-14 Kgs/ Cm2 |
ACCESSORIES
ELECTRICAL CONTROL PANEL
| Description | Specification |
|---|---|
| MOC | Plastic |
| Power | Single Phase |
| Condutivity Meter | Inbuilt |
| LPS Adjuster | Inbuilt |
| HPS Adjuster | Inbuilt |
WET PANEL
| Description | Specification |
|---|---|
| MOC | Plastic |
| Flow Meters | Two |
| Pressure Gauges | Two |
| LPS | One |
| HPS | One |
SKID
| Description | Specification |
|---|---|
| MOC | Stainless steel |
PIPING
| Description | Specification |
|---|---|
| Raw Water Pump To Micron Filter | UPVC |
| Micron Filter To Flow Meters | UPVC |
| Product Line | UPVC (As Per FDA &NSF) |
| Reject Line | UPVC |